Plumbing Basics: An Essential for Installing a Bathtub
Plumbing Basics: An Essential for Installing a Bathtub
Blog Article
They are making several good points related to Tools You Need to Install a New Bathtub as a whole in this post below.
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is also a moderately tough job. If the old tub is easily available, the job can move rapidly; if you need to open up a wall surface to remove the old tub and place the brand-new bathtub, the task is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need an assistant to move out the old tub and embeded in the brand-new one. Ensure you have actually certified on your own for the job as well as are comfortable trying it. As opposed to working with a service provider to take over a halfway-completed job, it is better to consider using one before you begin. Chances are you may require an expert plumber to make tube links.
This article will help you mount a new tub in your bathroom if you have actually already purchased a new bathtub and also don't need to change the arrangement of your previous water system pipes.
Your tools and material checklist need to consist of the following:
Getting ready for the Installment
To start with, the supporting frame provided with the bathroom must be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is separate the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be rather troublesome as a result of the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have been gotten rid of, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bath tub
Using both wooden boards under its feet, place the tub in the called for setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the tub till the level reviews degree.
To set up taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Activate the water supply and inspect all joints and also new pipework for leakages as well as tighten them if essential. Load the bath tub as well as also examine the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, repair the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the tub should wait up until the bathtub has been used a minimum of once as this will certainly settle it right into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin making certain that the washing machines are in area in between the tap as well as the sink. Protect the faucet in position with the producer provided backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The former type should be attached to the faucet finishes first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface between the bath as well as the tiling, bring about difficulties with wetness and possible leaks to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes as well as cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before securing, to allow for the activity experienced when the tub is in use. The sealer can fracture relatively early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently available on the marketplace. It is recommended to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about How to Install a Bathtub Yourself? Create a short review directly below. We would be glad to know your thoughts about this write up. We are looking forward that you come back again in the future. Make sure you take a moment to promote this blog if you appreciated it. I praise you for your time. Kindly pay a visit to our site back soon.
Book With Us Today! Report this page